[PC-BSD Testing] 8.2-RC2 64bit testing results (lang, proxy java & flash plugins problem)

Łukasz pickman at wp.pl
Thu Jan 27 23:59:07 PST 2011


Greetings,
 Yesterday I installed PCBSD 8.2-RC2 on my laptop - HP Compaq 6910p
(64bit). I see huge progress comparing to 8.0 - bravo!
Anyway I noticed several problems:
1. During installation procedure, when I choose Polish language
settings I don't see description near some of the checkboxes. Also,
after installation, pcSoftwareManager doesn't display tab name
properly - see the attachment.
2. I need webbrowser with java and flash support (in fact java is much
more important in this situation). Firefox 3.6 won't work with java.
Konqueror works, but unfortunately some of my office application
doesn't support it. Opera works with flash, but not with java.
SeaMonkey 2.0.11 supports both plugins, but there is a bug with PSM
and it doesn't support https pages. So my only solution here is
SeaMonkey 2.0.10. Is that correct? All tested webbrowsers I installed
via pbi as 64 bit applications, the same for java-jre (java version
"1.6.0_07").
3. We use proxy in the office. I provided address of proxy.pac file
for System Settings in KDE. All tested application works fine,
excluding pcSoftwareManager - it is able to see whether new updates
appear but is not able to download.
4. When I configure wlan0 device to connect to my wireless network by
the first time, link is very unstable, see below:
Jan 27 20:55:46 volkov kernel: wlan0: link state changed to DOWN
Jan 27 20:55:46 volkov wpa_supplicant[4404]: CTRL-EVENT-DISCONNECTED -
Disconnect event - remove keys
Jan 27 20:55:46 volkov wpa_supplicant[4403]: CTRL-EVENT-DISCONNECTED -
Disconnect event - remove keys
Jan 27 20:55:48 volkov wpa_supplicant[4404]: CTRL-EVENT-SCAN-RESULTS
Jan 27 20:55:48 volkov wpa_supplicant[4403]: CTRL-EVENT-SCAN-RESULTS
Jan 27 20:55:48 volkov wpa_supplicant[4403]: Trying to associate with
00:11:2a:5e:fa:30 (SSID='cysnet' freq=2432 MHz)
Jan 27 20:55:48 volkov wpa_supplicant[4404]: Trying to associate with
00:11:2a:5e:fa:30 (SSID='cysnet' freq=2432 MHz)
Jan 27 20:55:48 volkov wpa_supplicant[4403]: Associated with 00:11:2a:5e:fa:30
Jan 27 20:55:48 volkov kernel: wlan0: link state changed to UP
Jan 27 20:55:48 volkov wpa_supplicant[4404]: Associated with 00:11:2a:5e:fa:30
Jan 27 20:55:48 volkov wpa_supplicant[4404]: WPA: Invalid EAPOL-Key
MIC when using TPTK - ignoring TPTK
Jan 27 20:55:48 volkov wpa_supplicant[4404]: WPA: Could not verify
EAPOL-Key MIC - dropping packet
Jan 27 20:55:48 volkov wpa_supplicant[4403]: WPA: Key negotiation
completed with 00:11:2a:5e:fa:30 [PTK=CCMP GTK=CCMP]
Jan 27 20:55:48 volkov wpa_supplicant[4403]: CTRL-EVENT-CONNECTED -
Connection to 00:11:2a:5e:fa:30 completed (reauth) [id=0 id_str=]
Jan 27 20:55:58 volkov wpa_supplicant[4404]: Authentication with
00:11:2a:5e:fa:30 timed out.
Jan 27 20:55:58 volkov kernel: wlan0: link state changed to DOWN
Jan 27 20:55:58 volkov wpa_supplicant[4403]: CTRL-EVENT-DISCONNECTED -
Disconnect event - remove keys
Jan 27 20:55:58 volkov wpa_supplicant[4404]: CTRL-EVENT-DISCONNECTED -
Disconnect event - remove keys
Jan 27 20:56:01 volkov wpa_supplicant[4404]: CTRL-EVENT-SCAN-RESULTS
Jan 27 20:56:01 volkov wpa_supplicant[4404]: Trying to associate with
00:11:2a:5e:fa:30 (SSID='cysnet' freq=2432 MHz)
Jan 27 20:56:01 volkov wpa_supplicant[4403]: CTRL-EVENT-SCAN-RESULTS
Jan 27 20:56:01 volkov wpa_supplicant[4403]: Trying to associate with
00:11:2a:5e:fa:30 (SSID='cysnet' freq=2432 MHz)
Jan 27 20:56:01 volkov wpa_supplicant[4403]: Associated with 00:11:2a:5e:fa:30
Jan 27 20:56:01 volkov kernel: wlan0: link state changed to UP
after reboot it works fine.
5. I tried to use Virtualbox, but without success. At the end of the
installation process, a window with question appears, but it is blank
(see problem 1). I assume it asks me about approval for modification
of /boot/loader.conf and /etc/rc.conf. I agree and installation
finishes. After this, I'm not able to start Virtualbox instantly
(that's ok, it needs module loaded and according to FreeBSD wiki, this
should be done during booting to avoid crash). After reboot, system is
not able to start. It loads modules and stops displaying hundreds of
"Fatal trap 12" errors.
6. From time to time, system hangs. Just before this I see that Xorg
process eats ~100% CPU. I think that this can be some bug in display
driver. I switched from ati3d to ati driver and problem is not so
frequent anymore, but still happens. Graphic card is Radeon M64S. I've
also tested RAM and I found nothing. Any ideas what can be wrong?

Thank you in advance for all the suggestions.

Lukasz
-------------- next part --------------
PC-BSD 8.2-RC2 Diagnostic Sheet
Generated: ptk 28 sty 2011 07:55:34 UTC

-----------------Dmesg Output-------------------------

Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-RC2 #5: Tue Jan 11 16:32:56 PST 2011
    root at build8x64.pcbsd.org:/usr/obj/usr/pcbsd-build82/fbsd-source/8.2/sys/PCBSD amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Duo CPU     T8300  @ 2.40GHz (2394.02-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x10676  Family = 6  Model = 17  Stepping = 6
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x8e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 2031099904 (1937 MB)
ACPI APIC Table: <HP     30C1    >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Changing APIC ID to 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
Cuse4BSD v0.1.13 @ /dev/cuse
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
acpi0: <HPQOEM SLIC-MPC> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 7ef00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_ec0: <Embedded Controller: GPE 0x16> port 0x62,0x66 on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x4000-0x40ff mem 0xd0000000-0xd3ffffff,0xd8400000-0xd840ffff irq 16 at device 0.0 on pci1
pci0: <simple comms> at device 3.0 (no driver attached)
atapci0: <Intel ATA controller> port 0x5000-0x5007,0x5008-0x500b,0x5010-0x5017,0x5018-0x501b,0x5020-0x502f irq 18 at device 3.2 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
pci0: <simple comms, UART> at device 3.3 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection 7.1.8> port 0x5040-0x505f mem 0xd8520000-0xd853ffff,0xd8540000-0xd8540fff irq 22 at device 25.0 on pci0
em0: Using an MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:1e:ec:8f:c2:84
uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0x5060-0x507f irq 16 at device 26.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x2f00
usbus0: <Intel 82801H (ICH8) USB controller USB-D> on uhci0
uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0x5080-0x509f irq 17 at device 26.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x2f00
usbus1: <Intel 82801H (ICH8) USB controller USB-E> on uhci1
ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem 0xd8541000-0xd85413ff irq 18 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> on ehci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci8: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pci16: <ACPI PCI bus> on pcib3
iwn0: <Intel(R) PRO/Wireless 4965BGN> mem 0xd8000000-0xd8001fff irq 17 at device 0.0 on pci16
iwn0: MIMO 2T3R, MoW2, address 00:21:5c:03:d8:45
iwn0: [ITHREAD]
iwn0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
iwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci40: <ACPI PCI bus> on pcib4
uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0x50a0-0x50bf irq 20 at device 29.0 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x2f00
usbus3: <Intel 82801H (ICH8) USB controller USB-A> on uhci2
uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0x50c0-0x50df irq 22 at device 29.1 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x2f00
usbus4: <Intel 82801H (ICH8) USB controller USB-B> on uhci3
uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0x50e0-0x50ff irq 18 at device 29.2 on pci0
uhci4: [ITHREAD]
uhci4: LegSup = 0x2f00
usbus5: <Intel 82801H (ICH8) USB controller USB-C> on uhci4
ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem 0xd8548000-0xd85483ff irq 20 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus6: EHCI version 1.0
usbus6: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> on ehci1
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib5
cbb0: <RF5C476 PCI-CardBus Bridge> mem 0xd8100000-0xd8100fff irq 18 at device 6.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [FILTER]
cbb1: <RF5C476 PCI-CardBus Bridge> mem 0xd8101000-0xd8101fff irq 19 at device 6.1 on pci2
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: [FILTER]
fwohci0: <1394 Open Host Controller Interface> mem 0xd8102000-0xd81027ff irq 20 at device 6.2 on pci2
fwohci0: [ITHREAD]
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:02:3f:99:29:41:31:10
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:02:3f:41:31:10
fwe0: Ethernet address: 02:02:3f:41:31:10
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:02:3f:99:29:41:31:10 @ 0xfffe00000000, S400, maxrec 2048
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x136c000
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
sdhci0: <RICOH R5C822 SD> mem 0xd8103000-0xd81030ff irq 19 at device 6.3 on pci2
sdhci0: 1 slot(s) allocated
sdhci0: [ITHREAD]
pci2: <base peripheral> at device 6.4 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH8M UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x5100-0x510f irq 16 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci1
ata0: [ITHREAD]
ahci0: <Intel ICH8M AHCI SATA controller> port 0x13f0-0x13f7,0x15f4-0x15f7,0x1370-0x1377,0x1574-0x1577,0x5140-0x515f mem 0xd8549000-0xd85497ff irq 21 at device 31.2 on pci0
ahci0: [ITHREAD]
ahci0: AHCI v1.10 with 3 3Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich0: [ITHREAD]
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
acpi_tz2: <Thermal Zone> on acpi0
acpi_tz3: <Thermal Zone> on acpi0
acpi_tz4: <Thermal Zone> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71,0x72-0x73 irq 8 on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77a irq 7 drq 1 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0)  (me) 
firewire0: bus manager 0 
ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is present;
            to enable, add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf.
ZFS filesystem version 4
ZFS storage pool version 15
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
acd0: DVDR <MATSHITADVD-RAM UJ-852S/1.02> at ata0-master PIO4 
pccard1: <unknown card> (manufacturer=0x0000, product=0x0000, function_type=254) at function 0
pccard1:    CIS info: RICOH, Bay8Controller
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub2: 4 ports with 4 removable, self powered
uhub6: 6 ports with 6 removable, self powered
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 
ugen0.2: <Broadcom Corp> at usbus0
(probe7:ata0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe7:ata0:0:0:0): CAM status: SCSI Status Error
(probe7:ata0:0:0:0): SCSI status: Check Condition
(probe7:ata0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
ada0 at ahcich0 bus 0 scbus1 target 0 lun 0
ada0: <TOSHIBA MK1652GSX LV011C> ATA-8 SATA 2.x device
ada0: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)cd0 at ata0 bus 0 scbus2 target 0 lun 0
cd0: <MATSHITA DVD-RAM UJ-852S 1.02> Removable CD-ROM SCSI-0 device 
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present

SMP: AP CPU #1 Launched!
ugen3.2: <vendor 0x08ff> at usbus3
Enter passphrase for ada0p4: 
GEOM_ELI: Device ada0p4.eli created.
GEOM_ELI: Encryption: AES-XTS 128
GEOM_ELI:     Crypto: software
Trying to mount root from zfs:tank0
wlan0: Ethernet address: 00:21:5c:03:d8:45
hdac0: <Intel 82801H High Definition Audio Controller> mem 0xd8544000-0xd8547fff irq 17 at device 27.0 on pci0
hdac0: HDA Driver Revision: 20100226_0142
hdac0: [ITHREAD]
hdac0: HDA Codec #0: Analog Devices AD1981HD
hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
hdac0: hdac_command_send_internal: TIMEOUT numcmd=1, sent=1, received=0
hdac0: Codec #1 is not responding! Probing aborted.
pcm0: <HDA Analog Devices AD1981HD PCM #0 Analog> at cad 0 nid 1 on hdac0
drm0: <ATI Mobility Radeon X2300> on vgapci0
info: [drm] MSI enabled 1 message(s)
vgapci0: child drm0 requested pci_enable_busmaster
info: [drm] Initialized radeon 1.31.0 20080613
info: [drm] Setting GART location based on new memory map
info: [drm] Loading R500 Microcode
info: [drm] Num pipes: 1
info: [drm] writeback test succeeded in 1 usecs
drm0: [ITHREAD]
ugen6.2: <Corsair> at usbus6
umass0: <Corsair Flash Voyager, class 0/0, rev 2.00/11.00, addr 2> on usbus6
umass0:  SCSI over Bulk-Only; quirks = 0x0000
umass0:3:0:-1: Attached to scbus3
(probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI status: Check Condition
(probe0:umass-sim0:0:0:0): SCSI sense: UNIT ATTENTION asc:28,0 (Not ready to ready change, medium may have changed)
da0 at umass-sim0 bus 0 scbus3 target 0 lun 0
da0: <Corsair Flash Voyager 1100> Removable Direct Access SCSI-0 device 
da0: 40.000MB/s transfers
da0: 15488MB (31719424 512 byte sectors: 255H 63S/T 1974C)
GEOM: da0: partition 1 does not start on a track boundary.
GEOM: da0: partition 1 does not end on a track boundary.

-----------------Messages Output----------------------

Jan 28 06:50:28 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 06:55:31 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:05:36 volkov last message repeated 2 times
Jan 28 07:10:25 volkov wpa_supplicant[482]: WPA: Group rekeying completed with 00:1e:2a:5e:fa:30 [GTK=CCMP]
Jan 28 07:10:38 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:15:41 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:16:28 volkov su: BAD SU plluksie to root on /dev/pts/3
Jan 28 07:16:35 volkov su: plluksie to root on /dev/pts/3
Jan 28 07:16:36 volkov su: plluksie to root on /dev/pts/3
Jan 28 07:19:00 volkov last message repeated 2 times
Jan 28 07:20:43 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:25:46 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:30:48 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:35:51 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:40:26 volkov wpa_supplicant[482]: WPA: Group rekeying completed with 00:1e:2a:5e:fa:30 [GTK=CCMP]
Jan 28 07:40:53 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:42:19 volkov sudo: plluksie : TTY=pts/1 ; PWD=/usr/home/plluksie ; USER=root ; COMMAND=sudoedit /etc/rc.conf
Jan 28 07:45:55 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:50:58 volkov wpa_supplicant[482]: CTRL-EVENT-SCAN-RESULTS 
Jan 28 07:55:20 volkov su: plluksie to root on /dev/pts/3

------------------pciconf-----------------------------

hostb0 at pci0:0:0:0:	class=0x060000 card=0x30c1103c chip=0x2a008086 rev=0x0c hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Mobile PM965/GM965/GL960 Express Processor to DRAM Controller'
    class      = bridge
    subclass   = HOST-PCI
pcib1 at pci0:0:1:0:	class=0x060400 card=0x30c1103c chip=0x2a018086 rev=0x0c hdr=0x01
    vendor     = 'Intel Corporation'
    device     = 'Mobile PM965/GM965/GL960 Express PCIe Root Port'
    class      = bridge
    subclass   = PCI-PCI
none0 at pci0:0:3:0:	class=0x078000 card=0x30c1103c chip=0x2a048086 rev=0x0c hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Intel PCI communication controller (Q965/Q96)'
    class      = simple comms
atapci0 at pci0:0:3:2:	class=0x010185 card=0x30c1103c chip=0x2a068086 rev=0x0c hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Mobile PT IDER Controller'
    class      = mass storage
    subclass   = ATA
none1 at pci0:0:3:3:	class=0x070002 card=0x30c1103c chip=0x2a078086 rev=0x0c hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Intel PCI Serial Port (Q965/Q963)'
    class      = simple comms
    subclass   = UART
em0 at pci0:0:25:0:	class=0x020000 card=0x30c1103c chip=0x10498086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Gigabit Network Connection Interface Controller (82566MM NIC)'
    class      = network
    subclass   = ethernet
uhci0 at pci0:0:26:0:	class=0x0c0300 card=0x30c1103c chip=0x28348086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI *4'
    class      = serial bus
    subclass   = USB
uhci1 at pci0:0:26:1:	class=0x0c0300 card=0x30c1103c chip=0x28358086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI *5'
    class      = serial bus
    subclass   = USB
ehci0 at pci0:0:26:7:	class=0x0c0320 card=0x30c1103c chip=0x283a8086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'ICH8 Enhanced USB2 Enhanced Host Controller (81EC1043 (?))'
    class      = serial bus
    subclass   = USB
hdac0 at pci0:0:27:0:	class=0x040300 card=0x30c1103c chip=0x284b8086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Intel audio controller embedded with the 82801H chipset ( ICH8 chipset ) (82801H)'
    class      = multimedia
    subclass   = HDA
pcib2 at pci0:0:28:0:	class=0x060400 card=0x30c1103c chip=0x283f8086 rev=0x03 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 1'
    class      = bridge
    subclass   = PCI-PCI
pcib3 at pci0:0:28:1:	class=0x060400 card=0x30c1103c chip=0x28418086 rev=0x03 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 2'
    class      = bridge
    subclass   = PCI-PCI
pcib4 at pci0:0:28:4:	class=0x060400 card=0x30c1103c chip=0x28478086 rev=0x03 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 5'
    class      = bridge
    subclass   = PCI-PCI
uhci2 at pci0:0:29:0:	class=0x0c0300 card=0x30c1103c chip=0x28308086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI *1'
    class      = serial bus
    subclass   = USB
uhci3 at pci0:0:29:1:	class=0x0c0300 card=0x30c1103c chip=0x28318086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI *2'
    class      = serial bus
    subclass   = USB
uhci4 at pci0:0:29:2:	class=0x0c0300 card=0x30c1103c chip=0x28328086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI *3'
    class      = serial bus
    subclass   = USB
ehci1 at pci0:0:29:7:	class=0x0c0320 card=0x30c1103c chip=0x28368086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB2 EHCI *1'
    class      = serial bus
    subclass   = USB
pcib5 at pci0:0:30:0:	class=0x060401 card=0x30c1103c chip=0x24488086 rev=0xf3 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801 Family (ICH2/3/4/5/6/7/8/9-M) Hub Interface to PCI Bridge'
    class      = bridge
    subclass   = PCI-PCI
isab0 at pci0:0:31:0:	class=0x060100 card=0x30c1103c chip=0x28118086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801HBM (ICH8M) LPC Interface Controller'
    class      = bridge
    subclass   = PCI-ISA
atapci1 at pci0:0:31:1:	class=0x01018a card=0x30c1103c chip=0x28508086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) Ultra ATA Storage Controllers'
    class      = mass storage
    subclass   = ATA
ahci0 at pci0:0:31:2:	class=0x010601 card=0x30c1103c chip=0x28298086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Mobile SATA AHCI Controller'
    class      = mass storage
    subclass   = SATA
vgapci0 at pci0:1:0:0:	class=0x030000 card=0x30c1103c chip=0x71881002 rev=0x00 hdr=0x00
    vendor     = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.'
    device     = 'ATI MOBILITY /ATI RADEON X2300 (M54)'
    class      = display
    subclass   = VGA
iwn0 at pci0:16:0:0:	class=0x028000 card=0x11018086 chip=0x42298086 rev=0x61 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Intel Wireless WiFi Link 4965AGN(supporting 802.11a/b/g/Draft-N) (Intel 4965AGN)'
    class      = network
cbb0 at pci0:2:6:0:	class=0x060700 card=0x30c1103c chip=0x04761180 rev=0xb9 hdr=0x02
    vendor     = 'Ricoh Co Ltd'
    device     = 'Ricoh R/RL/5C476(II) (unknown)'
    class      = bridge
    subclass   = PCI-CardBus
cbb1 at pci0:2:6:1:	class=0x060700 card=0x30c1103c chip=0x04761180 rev=0xb9 hdr=0x02
    vendor     = 'Ricoh Co Ltd'
    device     = 'Ricoh R/RL/5C476(II) (unknown)'
    class      = bridge
    subclass   = PCI-CardBus
fwohci0 at pci0:2:6:2:	class=0x0c0010 card=0x30c1103c chip=0x08321180 rev=0x03 hdr=0x00
    vendor     = 'Ricoh Co Ltd'
    device     = 'IEEE 1394 (4 pin firewire) chip) (30CF103C)'
    class      = serial bus
    subclass   = FireWire
sdhci0 at pci0:2:6:3:	class=0x080500 card=0x30c1103c chip=0x08221180 rev=0x20 hdr=0x00
    vendor     = 'Ricoh Co Ltd'
    device     = 'SDA Standard Compliant SD Host Controller (R5C832)'
    class      = base peripheral
    subclass   = SD host controller
none2 at pci0:2:6:4:	class=0x088000 card=0x30c1103c chip=0x08431180 rev=0x10 hdr=0x00
    vendor     = 'Ricoh Co Ltd'
    device     = 'Ricoh SD/MMC Host Controller (R5C853)'
    class      = base peripheral

------------------xorg.conf---------------------------

# Xorg.conf file generated for PC-BSD

Section "ServerLayout"
    Identifier     "XFree86 Configured"
    Screen      0  "Screen0" 0 0
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
    Option	   "Clone" "off"
EndSection

Section "ServerFlags"
        Option         "AutoAddDevices" "Off"
EndSection

Section "Files"
    ModulePath      "/usr/local/lib/xorg/modules"
    FontPath        "/Programs/fonts/"
    FontPath        "/usr/local/lib/X11/fonts/cyrillic/"
    FontPath        "/usr/local/lib/X11/fonts/TrueType/"
    FontPath        "/usr/local/lib/X11/fonts/webfonts/"
    FontPath        "/usr/local/lib/X11/fonts/misc/"
    FontPath        "/usr/local/lib/X11/fonts/TTF/"
    FontPath        "/usr/local/lib/X11/fonts/Type1/"
    FontPath        "/usr/local/lib/X11/fonts/CID/"
    FontPath        "/usr/local/lib/X11/fonts/75dpi/"
    FontPath        "/usr/local/lib/X11/fonts/100dpi/"
    FontPath        "/usr/local/lib/X11/fonts/dejavu/"
    FontPath        "/usr/local/lib/X11/fonts/local/"
EndSection

Section "Module"
    Load           "ddc"
    Load           "dbe"
#    Load	   "dri"
    Load           "extmod"
#    Load	   "glx"
EndSection

Section "InputDevice"
    Identifier     "Keyboard0"
    Driver         "keyboard"
    Option         "XkbModel" "pc105"
    Option         "XkbLayout" "us"
    Option         "XkbVariant" ""
EndSection

Section "InputDevice"
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "auto"
    Option         "Device" "/dev/sysmouse"
    Option         "Buttons" "6"
    Option         "ZAxisMapping" "4 5"
    Option         "Emulate3Buttons"
EndSection


Section "Monitor"
    Identifier     "Monitor0"
    VendorName     "Monitor Vendor"
    ModelName      "Monitor Model"
EndSection


Section "Device"
    Identifier      "Card0"
    Screen           0
    Driver         "ati"
    VendorName     "ATI Video Driver"
    Option         "CPPIOMode" "yes" 
    BusID      "PCI:1:0:0"
EndSection


Section "Screen"
    Identifier     "Screen0"
    Device         "Card0"
    Monitor        "Monitor0"
    DefaultDepth   24
    SubSection     "Display"
        Depth      24 
        Modes      "1440x900"
    EndSubSection
EndSection

------------------RC File-----------------------------

background_dhclient="YES" 
compat5x_enable="YES" 
sshd_enable="YES" 
devd_enable="YES" 
devfs_system_ruleset="devfsrules_common" 
ldconfig_paths="/usr/lib/compat /usr/local/lib /usr/local/kde4/lib /usr/local/lib/compat/pkg"

# Disable Sendmail by default
sendmail_enable="NONE"

# Enable console mouse
moused_type="auto" 
moused_enable="YES" 

# Enable the pcbsd startup / shutdown scripts
pcbsdinit_enable="YES"
 
#Enable samba server 
samba_enable="YES" 
winbindd_enable="YES"
 
# Disable LPD  
lpd_enable="NO" 
 
# Enable CUPS 
cupsd_enable="YES" 
linux_enable="YES"
 
# FSCK Enhancements 
fsck_y_enable="YES" 
 
# Denyhosts Startup 
denyhosts_enable="YES" 

# powerd: adaptive speed while on AC power, adaptive while on battery power
powerd_enable="YES"
powerd_flags="-a hiadaptive -b adaptive" # set CPU frequency

# enable HAL / DBUS
dbus_enable="YES"
hald_enable="YES"

# Enables support for HPLIP
hpiod_enable="NO"
hpssd_enable="NO"

# Enable the firewall
pf_rules="/etc/pf.conf"
pf_enable="YES"
pf_flags=""

# Enable sound-support
snddetect_enable="YES"
mixer_enable="YES"

# Enable avahi_daemon
avahi_daemon_enable="YES"

# Run the port jail
portjail_enable="YES"

# Added for sound support in the portjail, access to /dev/random, /dev/null, etc.
jail_pcbsd_devfs_enable="YES"

# Start the swapmonitor
swapmonitor_enable="YES"

# Enable IPV6 support
ipv6_enable="YES"

# Enable BSDStats
bsdstats_enable="YES"

# Enable webcamd
webcamd_enable="YES"

# Disable writing syslogs to remote devices by default
syslogd_flags="-ss"
ntpd_enable="YES"
ntpd_sync_on_start="YES"
keymap="pl_PL.ISO8859-2"
# Auto-Enabled NICs from pc-sysinstall
ifconfig_em0="DHCP"
wlans_iwn0="wlan0"
ifconfig_wlan0="WPA SYNCDHCP"
hostname="volkov"
zfs_enable="YES"
warden_enable="YES"

------------------Loader File-------------------------

# Kernel Options
kern.ipc.shmseg=1024
kern.ipc.shmmni=1024
kern.maxproc=10000

# Load Wireless Support
if_ipw_load="YES"
if_iwi_load="YES"
if_wpi_load="YES"
if_iwn_load="YES"
if_bwn_load="YES"
legal.intel_ipw.license_ack=1
legal.intel_iwi.license_ack=1
legal.intel_wpi.license_ack=1
legal.intel_iwn.license_ack=1

# Enable usb Webcam Support
cuse4bsd_load="YES"
pwc_load="YES"

# Load mmc card-reader support
mmc_load="YES"
mmcsd_load="YES"

# Load additional sata device support
ahci_load="YES"
siis_load="YES"
sdhci_load="YES"

# Load support for scd
scd_load="YES"

# Load sound-support
sound_load="YES"
snd_uaudio_load="YES"

# Load geom support
geom_journal_load="YES"
geom_uzip_load="YES"
geom_mirror_load="YES"
geom_eli_load="YES"

# Load Serial Bus Protocol Support
sbp_load="YES"

# Load File-System Support
libiconv_load="YES"
libmchain_load="YES"
cd9660_iconv_load="YES"
msdosfs_iconv_load="YES"
ntfs_load="YES"
ntfs_iconv_load="YES"
udf_load="YES"
udf_iconv_load="YES"
zfs_load="YES"
tmpfs_load="YES"

# Disable acpi throttle by default, fixes issues with powerd and later AMDs
hint.acpi_throttle.0.disabled="1"

# Fix crashes on 32bit with Nvidia
machdep.disable_mtrrs=1
sem_load="YES"
geli_ada0p4_keyfile0_load="YES"
geli_ada0p4_keyfile0_type="ada0p4:geli_keyfile0"
geli_ada0p4_keyfile0_name="/boot/keys/ada0p4.key"
vfs.root.mountfrom="zfs:tank0"

------------------Free Space--------------------------

Filesystem           1M-blocks  Used  Avail Capacity  Mounted on
tank0                   111750   257 111492     0%    /
devfs                        0     0      0   100%    /dev
/dev/label/boot0           484   250    194    56%    /boot-mount
procfs                       0     0      0   100%    /proc
linprocfs                    0     0      0   100%    /compat/linux/proc
tank0/usr               144660 33167 111492    23%    /usr
tank0/var               111725   232 111492     0%    /var
/tmp                    111750   257 111492     0%    /usr/jails/portjail/tmp
/media                  111750   257 111492     0%    /usr/jails/portjail/media
/usr/home               144660 33167 111492    23%    /usr/jails/portjail/usr/home
devfs                        0     0      0   100%    /usr/jails/portjail/dev
procfs                       0     0      0   100%    /usr/jails/portjail/proc
linprocfs                    0     0      0   100%    /usr/jails/portjail/compat/linux/proc
/dev/msdosfs/SYSRESC     15472  1609  13863    10%    /media/SYSRESC

------------------System Processes--------------------

last pid: 22091;  load averages:  0.67,  0.47,  0.40  up 0+01:24:47    07:55:34
270 processes: 1 running, 269 sleeping

Mem: 1253M Active, 31M Inact, 542M Wired, 25M Cache, 211M Buf, 101M Free
Swap: 4062M Total, 516K Used, 4061M Free


  PID USERNAME    THR PRI NICE   SIZE    RES STATE   C   TIME   WCPU COMMAND
 3471 plluksie      1  52    0   116M 29220K select  0   4:46 12.89% npviewer.bin
22015 root          2  44    0   219M 42424K kqread  1   0:01 10.45% kcmshell4
 2676 root          1  48    0   369M   264M select  0   3:55  8.79% Xorg
13831 plluksie      1  46    0   116M 29220K futex   0   1:29  4.98% npviewer.bin
 2960 plluksie      4  68    0   623M   115M select  0   4:42  4.69% kdeinit4
21951 plluksie      1  44    0   229M 45640K select  1   0:02  1.95% systemsettings
 5525 plluksie      8  44    0   503M   251M kqread  1   2:07  1.37% opera
22035 root          1  52    0   101M 20620K select  0   0:00  0.20% kdeinit4
22036 root          1  44    0   100M 20080K select  0   0:00  0.20% kdeinit4
 2955 plluksie      3  76    0   352M 47376K kqread  0   0:08  0.10% kwin
 3424 plluksie      3  46    0   435M   132M ucond   1   1:01  0.00% kdeinit4
 3192 plluksie      2  53    0   347M 42756K kqread  0   0:44  0.00% kdeinit4
 5620 plluksie      1  44    0   308M 24092K select  1   0:39  0.00% operapluginwrapper.
13254 plluksie     12  44    0   258M   122M ucond   1   0:19  0.00% firefox-bin
 3467 plluksie      1  44    0   175M 28720K select  0   0:11  0.00% nspluginviewer
 8457 plluksie      2  44    0   321M 59384K kqread  0   0:07  0.00% kdeinit4
11892 plluksie      2  50    0   246M 39760K select  0   0:06  0.00% konsole
 2895 plluksie      1  44    0 10168K  3276K select  1   0:04  0.00% dbus-daemon



-------------- next part --------------
A non-text attachment was scrubbed...
Name: settings.png
Type: image/png
Size: 34370 bytes
Desc: not available
URL: <http://lists.pcbsd.org/pipermail/testing/attachments/20110128/e7c1303d/attachment-0001.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Xorg.0.log
Type: application/octet-stream
Size: 31660 bytes
Desc: not available
URL: <http://lists.pcbsd.org/pipermail/testing/attachments/20110128/e7c1303d/attachment-0001.obj>


More information about the Testing mailing list