[PC-BSD Testing] Runports -- failure update

Ian Robinson fitchkendall at gmail.com
Sun Mar 15 10:38:21 PST 2009


I loaded runports (root) again.  It stopped and generated the same error
message as before, so I installed icu-3.8.1_1 independently from ports.

I re-ran 'make' and it quickly continued the installation.

The routine generated numerous warnings about 'automake 1.10' and 'automake
1.0' and 'autoconf' were not installed on the system, but the process
continued.  Here is a typical example of those error messages:


gmake[3]: Entering directory `/usr/ports/devel/glib20/work/glib-2.18.4'
 cd . && /bin/sh /usr/ports/devel/glib20/work/glib-2.18.4/missing --run
automake-1.10 --gnu  Makefile
automake-1.10: not found
WARNING: `automake-1.10' is missing on your system.  You should only need it
if
         you modified `Makefile.am', `acinclude.m4' or `configure.in'.
         You might want to install the `Automake' and `Perl' packages.
         Grab them from any GNU archive site.
cd . && /bin/sh /usr/ports/devel/glib20/work/glib-2.18.4/missing --run
autoconf
autoconf: not found
WARNING: `autoconf' is missing on your system.  You should only need it if
         you modified `configure.in'.  You might want to install the
         `Autoconf' and `GNU m4' packages.  Grab them from any GNU
         archive site.


checking resolv.h usability...
no

checking resolv.h presence...
yes

configure: WARNING: resolv.h: present but cannot be
compiled

configure: WARNING: resolv.h:     check for missing prerequisite
headers?
configure: WARNING: resolv.h: see the Autoconf
documentation

configure: WARNING: resolv.h:     section "Present But Cannot Be
Compiled"
configure: WARNING: resolv.h: proceeding with the preprocessor's
result
configure: WARNING: resolv.h: in the future, the compiler will take
precedence
configure: WARNING:     ##
---------------------------------------------------------------------
##
configure: WARNING:     ## Report this to
http://bugzilla.gnome.org/enter_bug.cgi?product=ORBit2##
configure: WARNING:     ##
--------------------------------------------------------------------- ##



I added autoconf-2.62 from ports
I added Automake-1.10.1 from ports

Then I began to generate these error messages:

gmake[4]: Entering directory `/usr/ports/devel/ORBit2/work/ORBit2-2.14.17'
gmake[4]: Leaving directory `/usr/ports/devel/ORBit2/work/ORBit2-2.14.17'
cd .. && gmake  am--refresh
gmake[4]: Entering directory `/usr/ports/devel/ORBit2/work/ORBit2-2.14.17'
 cd . && /bin/sh /usr/ports/devel/ORBit2/work/ORBit2-2.14.17/missing --run
automake-1.10 --gnu  Makefile
configure.in:43: version mismatch.  This is Automake
1.10.1,
configure.in:43: but the definition used by this
AM_INIT_AUTOMAKE
configure.in:43: comes from Automake 1.10.2.  You should
recreate
configure.in:43: aclocal.m4 with aclocal and run automake
again.
WARNING: `automake-1.10' is probably too old.  You should only need it
if
         you modified `Makefile.am', `acinclude.m4' or `configure.in'.

         You might want to install the `Automake' and `Perl'
packages.
         Grab them from any GNU archive
site.
cd . && /bin/sh /usr/ports/devel/ORBit2/work/ORBit2-2.14.17/missing --run
autoconf
/bin/sh ./config.status --recheck


So I tried to run 'automake" without success:

# cd /usr/local/bin
# automake
automake-1.10: `configure.ac' or `configure.in' is required


I also tried to install "ORBit2" from ports without success

libtool: Version mismatch error.  This is libtool 2.2.6, but the
libtool: definition of this LT_INIT comes from an older release.
libtool: You should recreate aclocal.m4 with macros from libtool 2.2.6
libtool: and run autoconf again.
gmake[3]: *** [orbit-idl-2] Error 63
gmake[3]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/src/idl-compiler'
gmake[2]: *** [install-am] Error 2
gmake[2]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/src/idl-compiler'
gmake[1]: *** [install-recursive] Error 1
gmake[1]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/src'
gmake: *** [install-recursive] Error 1
*** Error code 2

Stop in /usr/ports/devel/ORBit2.

It was not long after that when the entire process stopped at this point:

config.status: creating config.h
config.status: config.h is unchanged
config.status: executing depfiles commands
config.status: executing libtool commands
gmake[8]: Leaving directory `/usr/ports/devel/ORBit2/work/ORBit2-2.14.17'
gmake[8]: Entering directory `/usr/ports/devel/ORBit2/work/ORBit2-2.14.17'
gmake[8]: Leaving directory `/usr/ports/devel/ORBit2/work/ORBit2-2.14.17'
gmake[7]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/include/orbit/orb-core'
gmake[7]: Entering directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/include/orbit/orb-core'
gmake[7]: *** No rule to make target
`../../../src/idl-compiler/orbit-idl-2', needed by `orbit-interface.h'.
Stop.
gmake[7]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/include/orbit/orb-core'
gmake[6]: *** [all-recursive] Error 1
gmake[6]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/include/orbit'
gmake[5]: *** [all] Error 2
gmake[5]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/include/orbit'
gmake[4]: *** [all-recursive] Error 1
gmake[4]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/include'
gmake[3]: *** [all] Error 2
gmake[3]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/src/orb/include'
gmake[2]: *** [install-recursive] Error 1
gmake[2]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/src/orb'
gmake[1]: *** [install-recursive] Error 1
gmake[1]: Leaving directory
`/usr/ports/devel/ORBit2/work/ORBit2-2.14.17/src'
gmake: *** [install-recursive] Error 1
*** Error code 2

Stop in /usr/ports/devel/ORBit2.
*** Error code 1

Stop in /usr/ports/devel/py-orbit.
*** Error code 1

Stop in /usr/ports/x11-toolkits/py-gnome2.
*** Error code 1


Elapsed time to this point was approx. 4.5 Hours
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.pcbsd.org/pipermail/testing/attachments/20090315/609b437a/attachment-0001.html 


More information about the Testing mailing list